Tools You Need to Install a New Bath Tub
Tools You Need to Install a New Bath Tub
Blog Article
The article author is making a few great points related to A Step-by-Step Guide to Installing a Bathtub as a whole in this article following next.
Setting up a bath tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a moderately tough task. If the old tub is readily easily accessible, the task can relocate quickly; if you have to open a wall surface to get rid of the old bathtub and place the brand-new bath tub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as set in the brand-new one. See to it you have actually qualified yourself for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is much better to take into consideration using one prior to you begin. Opportunities are you may require a specialist plumber to make tube connections.
This article will certainly help you set up a brand-new bath tub in your shower room if you have actually already bought a brand-new bathtub and also don't require to transform the setup of your previous water supply pipelines.
Your devices and also product list need to consist of the following:
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, activate the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing taps can be fairly bothersome due to the limited gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. When the supply pipes have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the tap and also the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The previous type must be attached to the tap ends initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Using both wood boards under its feet, place the bath tub in the required position. The wooden boards are useful in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub till the spirit level reads level.
To mount faucets, fit all-time low of the furthest flexible tap port to the proper supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water supply and check all joints as well as new pipework for leaks as well as tighten them if needed. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has actually been used at the very least once as this will certainly settle it into its last placement.
Preparing for the Installation
Firstly, the supporting framework supplied with the bath should be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets unit to avoid stress on the tub.
Fit the flexible faucet connectors to the bottom of both faucets using 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you use all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final placement.
Tiling Around the Bath tub
In the location where the bathroom meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a rigid seal, triggering the water to penetrate the wall in between the bathroom and also the tiling, causing problems with moisture and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and also installations. They are sold in tubes and cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in use. The sealer can break fairly very early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly readily available on the market. It is recommended to fit the floor tiles making use of waterproof or water-proof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were guided to that editorial about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from an acquaintance on a different website. Those who liked our article kindly don't forget to pass it around. Kudos for your time. Come back soon.
Schedule Estimate
Report this page